« PREV: 30″H X 88.5″W X 34″D (90 RU) White Triple Bay Outdoor Enclosure

NEXT: 50″H X 88.5″W X 25″D (78 RU) Triple Bay Outdoor Enclosure »

30″H X 88.5″W X 42″D (90 RU) Triple Bay Outdoor Enclosure

3OD-30DDXC

90 Racking Units Total
6 sets of Adjustable 19″ or 23″ Racking Rails w/ RU Markings and Passthru Holes
3 Front and 3 Rear Doors
3 Point Padlocking Handles
Heavy Duty Lifting Hooks
Door Windlocks
**Cabinet is Same as Above Except Painted Cream**

This Triple Bay Design is 30″ High and 88.5″ Wide and 42″ Deep. It comes with Six Sets of Standard 19″ or 23″ 15 RU (90 RU’s Total) Racking Rails w/ RU Markings. Low Profile Racking Hub that will allow you side by side Triple Bay Racking. Nema Outdoor Wireless LTE/4G/Wimax Triple Bay Racking Enclosure

View Other Photos of Triple Door Enclosures CLICK HERE

3OD-30DDXC Specs Sheet

3OD Drawing Spec Sheet

Wind Load Study

(CLICK ON TABS BELOW FOR MORE INFO)

Slide 1

Features
Alumishield®	Top cover, shades cabinet from the sun
Handles	Stainless steel – NEMA
Rails	Fully adjustable & Alodine coated
Doors	3 Front and 3 rear secured with three point locks and padlocking handles
Vents	Front & rear, top & bottom, filters supplied

Slide 2

Specifications – 3OD-30DDXC – 30″H X 88.5″W X 42″D (90 RU) Triple Bay Outdoor Enclosure

Weight

300 lbs. Assembled
425lbs. Shipping weight

Doors

Six – secured by three point locking system
Locks via customer supplied padlocks
Sealed with 13/16″ aluminum filled gaskets

Material

.125″ Alumiflex®
Finish: Flat aluminum
RF properties: Non-ferrous

Vents

Thirty bottom louvers per door
26 top louvers – In top cover-under Alumishield®
One removable filter panel per door
26 fixed filter pads in top cover

Handles

Stainless steel

Lifting Hooks

Four Standard

Exterior Screws

Stainless steel with NEMA washers & nylon locking nuts

Racking Specifications

Rails

Four sets standard (For additional rails see accessories)
Alodine coated
Holes tapped to 10 x 32 threads
Each rail supported by three R-STRUTS™
.125″ Alumiflex®
Rails will have the face utilizing 19″ racking and the mounting side to utilize 23″ racking. The left rail (19″ rack showing) will have two ground studs attached to the mounting face coming inward. There will be a hole at the top of each face of each rail for an optional ground strap. Rack units will be marked with etching depicting each RU and will have both a hole and etching separating each RU. The rails will be adjusted to fit inside an 3OD cabinet that has an extra 4″ width. The mounting holes will be adjusted to fit the new r-strut configuration. There will be 1.75″ passthrough holes between the RU-03 and the RU-04 marks on the face with the 23″ racking. Another 1.75″ passthrough will be on the face with the 19″ racking between the RU-04 and the RU-05 marks. Use Heyco 28882 snap bushing or equivalent in the 1.75″ cable passthrough holes. Hash Marks will seperate the RU’s.

Spacing

19″ EIA Standard

Positioning

All rails fully adjustable from front to rear

Useable Height

Useable Racking Height Has Been Revised to Only Fit in the Opening of the Door Jam. Which is Cabinet Height Minus 3.75″

Maximum: 26 13/16″

Total # of Rack Units: 90

15 RU’s per Rail Set

Useable Depth

Maximum: 38.50 ” Minimum: 36.75″

Door Opening Clearance

Height

26.75″

Width

23.625″

Exterior Cabinet Dimensions

Main Body

Height: 30.25″
Width: 88″

Total Occupied w/Mounting Feet Width 94.0”
Depth: 42.25″

Alumishield®

Hang down height: 1.75″
Width 93.25″
Depth: 44.50″

Handles

Protrude 1 7/8″

Total Space Occupied

Height: 30.50″
Width: 88″
Depth: 46″

Inside Clearance – Less Rails

Height

30″

Width

26.6875″ Each Compartment

Depth

See racking specs – useable depth chart above

Ratings

NEMA Class Types Available

Class 250 // 3R (Vented) // 4 (closed loop-a/c) // 4X

Paint Tested

1000 Hour salt spray

1000 Hour immersion

Warranty

Period

15 Years – Unconditional

Slide 3

Accessory Options
(C):	Powder baked on textured paint
R-2-30:	Two extra 30″ rails and mounting hardware
MTDX:	Mounting tray
CA-4:	Caster kit (4) & mounting hardware
SCR-432:	Rail Screws (4) 10×32
POP3 Options
POP3-1	3 = 6000 BTU Air Conditioner 220 Volts with 400 Watts Total Fan Heaters (18K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms
POP3-2	2 = 8000 BTU Air Conditioner 220 Volts with 800 Watts Total Fan Heaters (16K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms
POP3-3	3 = 6000 BTU Air Conditioner, 220 Volts with 400 Watts Total Fan Heaters (18K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms 3 Seperate Battery Compartment Tray’s for a 2OD
POP3-4	2 = 8000 BTU Air Conditioner 220 Volts with 800 Watts Total Fan Heaters (16K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms Battery Box 3 Seperate Battery Compartment Tray’s for a 2OD

Slide 4

Climate Control Options
Air Conditioners	view all options
Heater Options	view all options
AC & DC Fan Kits	view all options

Slide 5

Shipping Info
Standard	The 3OD-30DDXC is shipped fully assembled.

800-753-8459

30″H X 88.5″W X 42″D (90 RU) Triple Bay Outdoor Enclosure

3OD-30DDXC

Features

Specifications – 3OD-30DDXC – 30″H X 88.5″W X 42″D (90 RU) Triple Bay Outdoor Enclosure

Racking Specifications

Door Opening Clearance

Exterior Cabinet Dimensions

Inside Clearance – Less Rails

Ratings

Warranty

Accessory Options

POP3 Options

Climate Control Options

Shipping Info