Outdoor Enclosure / Cabinet 46 "H x 25"D

OOD-30DX-B1 -*Un-Painted OOD-30DXC-B1 -*Painted Cream 1 = OD-30DX (Top Enclosure) 30"H X 25"D X 25"W (ADJUSTABLE 19" or 23" Racking) 1 = BOD-DX (BATTERY BOX) (Bottom Enclosure) Outdoor Battery Box 16" High,25"Deep,25" Wide (Mounting Tray 2" H X 20 "D X 18.75"W) 1= Populated 4 Square Outlet   OOD-30DX-B2 -*Un-Painted OOD-30DXC-B2 -*Painted Cream 1 = OD-30DX (Top Enclosure) 30"H X 25"D X 25"W (ADJUSTABLE 19" or 23" Racking) 2 = BOD-DX (BATTERY BOX) (Bottom Enclosure) Outdoor Battery Box 16" High,25"Deep,25" Wide (Mounting Tray 2" H X 20 "D X 18.75"W) 1= Populated 4 Square Outlet

(Cabinet Part #)+(-B1)+(AC1) (B1 Brings on a Battery Box, or a B2 Brings on a Second Battery Box) **If Applicable** (AC1 Brings on 110V Airconditioner, or a AC2 Brings on 220V Airconditioner) **If Applicable**

Alumishield	Top cover, shades cabinet from the sun
Handles	Stainless steel - NEMA
Rails	Fully adjustable & alodine coated
Doors	Front and rear secured with three point locks and padlocking handles
Vents	Front & rear, top & bottom, filters supplied

General
Weight	150 lbs. assembled 230 Lbs. Shipping weight
Doors	Two - secured by three point locking system Locks via customer supplied padlocks sealed with 13/16" aluminum filled gaskets
Material	.125 ALUMIFLEX Finish: Flat aluminum RF properties: Non-ferrous
BOD-DX	:BATTERY BOX ENCLOSURE W/ SLIDE OUT BATTERY TRAY
Handles	Stainless steel, padlocking
Exterior Screws	Stainless with NEMA washers & nylon locking nuts
Racking Specifications
Rails	Two standard (For additional rails see accessories) Alodine coated Holes tapped to 10 x 32 threads Each rail supported by two R-STRUTS .125 Material (ALUMIFLEX)
Spacing	19" EIA STANDARD
Positioning	All rails fully adjustable from front to rear
Useable Height	30 inches (Top Enclosure)
Useable Depth	Maximum: 21 1/2" Minimum: 19 3/4" (See below)
*Section Starting & Ending Points Vertical Height Per section Effective Depth For Each Section Top 26.75" - 30.00" 3.25" 21.50" 26.57" - 26.75"  .18" 20.50" 21.00" - 26.57" 5.57" 21.50"         Center 9.00" - 21.00" 12.00" 19.75"         3.43" - 9.00" 5.57" 21.50" 3.25" - 3.43"  .18" 20.50" Bottom 0.00" - 3.25" 3.25" 21.50" *Section measurements start from the bottom of the cabinet (0.00") & run vertically upward towards the top of the cabinet (30.00")
Door Opening Clearance (Top Enclosure)
Height	25 13/16 inches
Width	19 1/2 inches
Exterior Cabinet Dimensions (TOTAL)
Main Body	Width: 25 1/2 inches Height: 46 1/4 inches Depth: 25 1/4 inches
Alumishield	Width: 28 1/16 inches Hang down height: 1 3/4 inches Depth: 29 inches
Handles	Protrude 1 7/8 inches
Total Space Occupied	Width: 28 1/16 inches Height: 46 1/2 inches Depth: 29 inches
Inside Clearance - Less Rails (Top Enclosure)
Width	23 5/8 inches
Height	30 inches
Depth	See racking spec's - useable depth chart above
Ratings
NEMA	Class 250 Type 4X
Paint Tested	500 Hour salt spray 500 hour immersion
Warranty
Period	15 Years - Unconditional

R-2-30:	Two extra 30" rails and mounting hardware
MTDX:	Mounting tray
CA-4:	Caster kit (4) & mounting hardware

Air Conditioners	view all options
Heater Options	view all options
AC & DC Fan Kits	view all options

Standard

The OOD-30DX-B1 is shipped fully assembled, but can easily be knocked down and reassembled at your site, if desired.