« PREV: 50″H X 59″W X 42″D (104 RU) Double Bay Outdoor Enclosure

NEXT: 62″H X 59″W X 34″D (132 RU) Outdoor Enclosure »

62″H X 59″W X 25″D (66 RU) Outdoor Enclosure

2OD-62DXC

Painted Cream
(4) – 19″ or 23″ Racking Rails
66 Total RU’s
2 Front and 2 Rear Doors
3 Point Padlocking Handles
Powder Baked-On Cream Paint
Lifting Hooks

This Double Bay Design is 62″ High and 59″ Wide and 25″ Deep. It comes with Two Sets of Standard 19″ or 23″ 33RU (66 RU’s Total) Racking Rails w/ RU Markings. Cabinet Racking Hubs that will allow you side by side, double racking bays. Nema Outdoor Wireless LTE/4G/Wimax Double Bay Racking Enclosure

Newly Modified Enclosure Spec Sheet

Wind Load Study

View Other Photos of Double Door Enclosures CLICK HERE

(CLICK ON TABS BELOW FOR MORE INFO)

Slide 1

Features
Alumishield™	Top cover, shades cabinet from the sun
Handles	Stainless steel – NEMA
Rails	Fully adjustable & Alodine coated
Doors	2 Front and 2 rear secured with three point locks and padlocking handles
Vents	Front & rear, top & bottom, filters supplied

Slide 2

Specifications – 2OD-62DXC – 62″H X 59″W X 25″D (66 RU) Double Bay Outdoor Enclosure

Weight

255 lbs. assembled

345 lbs. Shipping weight

Doors

Four – secured by three point locking system

Locks via customer supplied padlocks

Sealed with 13/16″ aluminum filled gaskets

Material

.125″ Alumiflex™

Finish: Flat aluminum

RF properties: Non-ferrous

Vents

Thirty bottom louvers per door

20 top louvers – In top cover-under Alumishield™

One removable filter panel per door

20 fixed filter pads in top cover

Handles

Stainless steel, padlocking

Exterior Screws

Stainless steel with NEMA washers & nylon locking

nuts

Racking Specifications

Rails

Two Sets Standard (For additional rails see accessories)

Alodine coated

Holes tapped to 10 x 32 threads

Each rail supported by three R-STRUTS™

.125″ Material (Alumiflex™)

Rails will have the face utilizing 19” racking and the mounting side to utilize 23” racking. The left rail (19” rack showing) will have two ground studs attached to the mounting face coming inward. There will be a hole at the top of each face of each rail for an optional ground strap. Rack units will be marked with etching depicting each RU and will have both a hole and etching separating each RU. The rails will be adjusted to fit inside an 2OD cabinet that has an extra 4” width. The mounting holes will be adjusted to fit the new r-strut configuration. There will be 1.75″ passthrough holes between the RU-03 and the RU-04 marks on the face with the 23″ racking. Another 1.75″ passthrough will be on the face with the 19″ racking between the RU-04 and the RU-05 marks. Use Heyco 28882 snap bushing or equivalent in the 1.75″ cable passthrough holes. Hash Marks will seperate the RU’s.

Spacing

19″ EIA Standard

Positioning

All rails fully adjustable from front to rear

Useable Height

Useable Racking Height Has Been Revised to Only Fit in the Opening of the Door Jam. Which is Cabinet Height Minus 3.75”

Maximum: 57.75″

Total # of Rack Units: 66

33 RU’s per Rail Set

Useable Depth

Maximum: 21.50″ Minimum: 19.75″

Door Opening Clearance

Height

58.25″

Width

23.625″

Exterior Cabinet Dimensions

Main Body

Height: 62″

Width: 59″

Total Occupied w/Mounting Feet Width 65.0”

Depth: 25″

Alumishield™

Width: 62.875″

Hang down height: 1.75″

Depth: 29.50″

Handles

Protrude 1 7/8″

Total Space Occupied

Height: 63.105″

Width: 65″

Depth: 28.75″

Inside Clearance – Less Rails

Height

62″

Width

26.6875″ Each Compartment

Depth

See racking specs – useable depth chart above

Ratings

NEMA

Class 250 // 3R (Vented) // 4 (closed loop-a/c) // 4X

Paint Tested

1000 Hour salt spray

1000 Hour immersion

Warranty

Period

15 Years – Unconditional

Slide 3

Accessory Options
R-2-62:	Two extra 50 ” rails and mounting hardware
MTDX:	Mounting tray
CA-4:	Caster kit (4) & mounting hardware
SCR-432:	Rail Screws (4) 10×32
POP2 Options
POP2-1	2 = 8000 BTU Air Conditioner, 220 Volts with 400 Watts Total Fan Heaters (12K Total BTU) Spool-Up Side Box 26″H X 22″W X 10″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms
POP2-2	2 = 8000 BTU Air Conditioner 220 Volts with 800 Watts Total Fan Heaters (16K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms
POP2-3	2 = 6000 BTU Air Conditioner, 220 Volts with 400 Watts Total Fan Heaters (12K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms 2 Seperate Battery Compartment Tray’s for a 2OD
POP2-4	2 = 8000 BTU Air Conditioner 220 Volts with 800 Watts Total Fan Heaters (16K Total BTU) Spool-Up Side Box 26″H X 22″W X 20″D LC-100 100 Amp Main Load Center w/ (4) 4-Square Outlets, (1) 220V Outlets 2 Fluorescent Lights Lifting Hooks Door Windlocks Door Alarms Battery Box 2 Seperate Battery Compartment Tray’s for a 2OD

Slide 4

Climate Control Options
Air Conditioners	view all options
Heater Options	view all options
AC & DC Fan Kits	view all options

Slide 5

Shipping Info
Standard	The 2OD-62DXC is shipped fully assembled, but can easily be knocked down and re-assembled at your site, if desired.

800-753-8459

62″H X 59″W X 25″D (66 RU) Outdoor Enclosure

2OD-62DXC

(CLICK ON TABS BELOW FOR MORE INFO)

Features

Specifications – 2OD-62DXC – 62″H X 59″W X 25″D (66 RU) Double Bay Outdoor Enclosure

Racking Specifications

Door Opening Clearance

Exterior Cabinet Dimensions

Inside Clearance – Less Rails

Ratings

Warranty

Accessory Options

POP2 Options

Climate Control Options

Shipping Info